safe working procedures grinding

Safe Work Procedure - Grinder - Angle Grinder

Burns from hot material or abrasion after/during grinding Safe Work Procedure Checklist: 1. PRE-Operation: Always begin by setting-up your work area safely to avoid the following: o Trip hazard, uncomfortable working conditions, electrical hazards, crowded work spaces (other students) and other dangerous situations

SAMPLE SAFE WORK PROCEDURES (TEMPLATES)

The Safe Work Procedures (Templates) presented herein are a sample guide to the subject . matters. and should not be considered as a legal authority. It does not remove, replace, or alter our obligations under any health and safety legislation. These are sample policies

Sample SAFE Work Procedure Templates: All Industries ...

Safe work procedures should be readily available to workers for reference. Remember to review your safe work procedures regularly to ensure they are accurate and effective. If a task or equipment changes, the safe work procedure(s) that relate to this change must also be updated.

GRINDING MACHINES - irem sen

work. Grinding machines have some special safety precautions that must be observed. These are in addition to those safety precautions described in Chapter 1. SAFETY PRECAUTIONS GRINDING MACHINE SAFETY Grinding machines are used daily in a machine shop. To avoid injuries follow the safety precautions listed below.

Free Safe Work Procedure - Angle Grinders

Safe Work Procedures are a very important weapon in your workplace safety training arsenal. ... Grinding work is necessary. Could a different tool be used with less risk? The correct size grinder is selected for the job. The correct flange and locking nut is in place for the type of disc being used.

Chapter 5: Surface Grinder – Manufacturing Processes 4-5

• Describe procedure select the grinding wheel. ... It should reach maximum speed before you try to use it for the safety reasons. If the wheel is working properly, manually used when very precise work needs to be done. Figure 1. Chevalier Surface Grinder. Dressing the Wheel. 1. Place the diamond wheel dresser onto the bed.

Portable Grinder Operating Procedures

work area. • Ensure work area is clean, free from slip, trip, and fall hazards and well maintained. • Keep the power cord away from the grinding wheel and the material being ground. • Have personnel not involved in the immediate work step away a safe distance from the grinding area. • Secure work with clamps or a vice to free

Safe Working Procedures and Instruction 100/115mm Disc …

Safe Working Procedures and Instruction 100/115mm Disc Grinder The risk of injury when using this machine is HIGH - Level 4 Risk This Disc Grinding machine is used for a range of off-hand grinding procedures. Uses of the Disc Grinding machine: a) Trimming irregularities from metal castings and forgings. b) Rough shaping of metals.

Safety Operating Procedures - Milling Machine

OPERATIONAL SAFETY CHECKS. Keep clear of moving machine parts. Follow correct clamping procedures. Keep overhangs as small as possible and check workpiece is secure. Set the correct speed to suit the cutter diameter, the depth of cut and the material. ENDING OPERATIONS AND CLEANING UP. Switch off the machine when work completed.

Safe Working Procedures Grinding

Safe Working Procedures Grinding. 202085ensp0183enpsafe work practice the grinder does not keep working correctly, does not adjust or lacks rest, uses the wrong type of grinding wheel or disc, or improper maintenance or unbalanced grinding on the side of grinding wheel causes personal injury as follows: obtain price

STANDARD OPERATING PROCEDURES for COMMON TOOL …

• Barrier cream, lab coats, safety glasses/goggles and safety shoes are to be used as the work dictates. • Long hair must be completely covered. • Grinding machines can be operated by technical staff only, or users listed on the "Accessibility List and eye protection must be worn. • …

Safe Operating Procedure BENCH GRINDER

Safe Operating Procedure BENCH GRINDER DO NOT use this equipment unless you have been instructed In its safe use and operation and have been given permission PERSONAL PROTECTIVE EQUIPMENT Safety glasses must be worn at all times in work areas. Long and loose hair must be contained. Hearing protection must be used. Sturdy footwear must be worn

safe working procedures grinding - delidish.be

Burns from hot material or abrasion after/during grinding Safe Work Procedure Checklist 1. PRE-Operation Always begin by setting-up your work area safely to avoid the following o Trip hazard uncomfortable working conditions electrical hazards crowded work spaces (other students) and other dangerous situations

Safe Work Procedure - Grinder - Pedestal and Bench Grinder

Burns from hot material after/during grinding Ensure work is appropriate to the machine – This machine is intended only for sharpening tools. It is not intended for shaping metal work pieces – Please see "Disc and Belt Sander" for shaping. Safe Work Procedure Checklist: 1. PRE-Operation:

Safe Working Procedures and Instruction Blade Sharpening ...

Safe Working Procedures and Instruction Blade Sharpening Machine The risk of injury when using this machine is MODERATE – Level 2 Risk The Makita Blade Sharpening Machine is a grinding machine that consists of a wide flat grinding wheel which rotates at low speed. The sharpening machine is used to sharpen knife, plane and chisel blades.

Safety Operating Procedure - Angle Grinder

grinding wheel or cause injury to the operator. 6. Secure and support the work piece using clamps, bench vices, etc. OPERATIONAL SAFETY CHECKS 1. Ensure all other students are clear of the immediate work area. 2. Keep fingers and hands & power cords clear of the grinding disc. 3. Never make adjustments while the angle grinder is running. 4.

SAFE OPERATING PROCEDURE ANGLE GRINDER

SAFE OPERATING PROCEDURE ANGLE GRINDER DO NOT use this equipment unless you have been instructed in its safe use and operation and given prior permission. PERSONAL PROTECTIVE EQUIPMENT PRE-OPERATIONAL SAFETY CHECKS Read Operators Manual and Risk assessment. Keep work area clean and tidy. Use only in designated grinding area – erect screens if ...

Safe Working Procedures and Safe Work Practices – IspatGuru

Benefits of safe working procedures and safe work practices. Safe working procedures and safe work practices at the work place have the following benefits. They provide standards for how work is to be carried out. They have a positive effect on quality, efficiency, and productivity. They prevent injury and illness by controlling potential hazards.

Concrete grinding, Practice of grinding, Health and safety

Safe operating procedures. Most companies have a Safe Operating Procedure (SOP) for each piece of equipment their workers take on-site that is potentially hazardous. They also generally complete a simple risk assessment before starting work at any new jobsite.

Grinding and cutting safely - The FABRICATOR

Safe Operating Procedure BENCH GRINDER DO NOT use this equipment unless you have been instructed In its safe use and operation and have been given permission PERSONAL PROTECTIVE EQUIPMENT Safety glasses must be worn at all times in work areas. Long and loose hair must be contained. Hearing protection must be used. Sturdy footwear must be worn

Safe Operating Procedures SOP 02 Bench Grinder

Procedure Reference Version Effective Date Review Date Page Number Date Printed WHS SOP 2 1.0 28/03/2018 28/03/2021 1 24/04/2018 SOP 02 – Bench Grinder DO NOT use this tool unless appropriately instructed in its safe use and operation and permission to operate has been given. COMPULSORY PPE AS NEEDED PPE PRE-OPERATIONAL SAFETY CHECKS 1.

Angle grinders | Department of Mines, Industry Regulation ...

safe work procedures specific to tasks to all operators. one-on-one supervision for people being trained and those who are unfamiliar with the use of angle grinders. general supervision for all angle grinding tasks. In developing the safe work procedures, questions to ask include:

Safe work procedures - WorkSafe Queensland

Safe work procedures ensure your workers are aware of the issues in their work tasks, and outline how to avoid injury or illness while doing these tasks. ... • Use only grinding discs for grinding (these are generally thicker) and the thinner cutting discs for cutting.

Standard Operating Procedure: Saw Cutting, Grinding, and ...

This procedure applies to wet sawing, grinding, and drilling/coring by Facilities operations Management (FM) personnel and contractors. 3.0 Responsibility 3.1 Facilities Management Environmental Resources Environmental Resources is responsible for working with staff …

Safe Operating Procedure Angle Grinder - RapidHire

Safe Operating Procedure Angle Grinder . SOP-0016 Version 1.0 Page 2 of 2 Approval Date September 2017. 9. Do not leave angle grinder running & only use the grinder when hand held. 10. Do not touch work piece immediately after grinding operation as it will be extremely hot. 11. Avoid breathing dust – wear suitable dust mask or respirator in ...

SAFE WORK PROCEDURES ANGLE GRINDER

SAFE WORK PROCEDURES ANGLE GRINDER SPECIAL INSTRUCTIONS: 1. Only persons who have been fully briefed on the safe use of angle grinders are to use these machines. ... Avoid grinding dust and debris in eyes eye protection must be worn. In restricted areas, or work where sparks are reflected back towar ds the user, the use of additional protection ...